LPG Propane Gas Fire Pit Control Safety Valve with Thermocouple Heater Flame Fai

Description

STYDDI LPG Propane Gas Fire Pit Control Safety Valve with Thermocouple Heater Flame Failure Control Parts for Low Pressure Propane, 3/8" Flare Inlet and Outlet, Suitable for BBQ Grill,Heater,Fire Pit
DESIGNED FOR FIREPLACES & FIRE PITS FOR PROPANE GAS: Flame failure valve with inlet and outlet with Flare thread 5/8”- 18UNF(3/8"Flare), 600mm thermocouple with M8*1 threaded head. Valve Spindle "D" shaft for 6mm knob, with M15 nut to fix on your panel plate.
THE DIY GAS APPLIANCE FOR EASY INSTALLATION: This can be a DIY gas appliance and installed vertically at the opening of the device container easily with necessary nuts.
CE&CSA CERTIFICATED FOR YOUR SAFETY: CE&CSA tested Main Control Valve In & Out with 3/8" Male Flare thread. NOTE: Keep the thermocouple to be heated and push the valve around 5-10s then release hand (if flame stops, adjust the location of thermocouple tip)
QUALITY WITH HIGH TEMPERATURE RESISTANCE: Made of high-quality brass material with heavy-duty construction for durable usage. Voltage＞20mV, thermocouple temperature resistant from -200 to 650 Degree Celsius.
PERFECTLY COMPATIBLE WITH ALL LOW PRESSURE HEATERS: Suitable for all kinds of low pressure heaters. Used for gas fireplace, fire pit, grill, BBQ stove, oven, catering cooker, patio heaters etc. ATTENTION: It’s a low pressure valve rated around 50000BTU need to work with thermocouple, please confirm your system before order to avoid return.
STYDDI Propane Gas Heater Fire Pit Main Control Valve with Thermocouple & Switch Specifications: Total Length: 600mm Head Thread Size: M8*1 End Connection Size for Valve: M8*1 Max BTU rating: 50000 Working pressure: 65mbar Voltage:＞20mV Thermocouple temperature: -200 ~ 650 Degree Celsius Time For Opening Valve: Less Than 10s Operation Instructions 1). Fix the valve on a plate or board of your grill or fire pit by the head screw and flange. 2). Connect your inlet and outlet hose on inlet and outlet side. (fix it tightly enough in case of gas leakage) 3). Fix the thermocouple nut M8 on the valve end tightly (Check if your valve end thread if 8mm before you buy) 4). Connect thermocouple and end thread well 5). Open gas by correct size knob and push your valve around 5-10s till the thermocouple head is heated enough. 6). Release your hand and it work properly If when you release hand, gas valve shut off again, please check a. If your thermocouple is always be heated on flame b. If the thermocouple end is well connected with valve c. If the inlet and outlet side well connect with hose you have Possible problems occurs during your use: Valve after turn can stick during using Reason: a. The thermocouple head is heated in right place, please adjust thermocouple tip position; b. The connection between thermocouple end and valve is connected tight enough or too tight, please adjust the screw again. Solution: Need to push valve first then turn the spindle and hold for few seconds, it cannot stick immediately may need 5-15 Seconds. Package Content: 1Pcs x Gas Control Valve with Thermocouple and Knob Switch
SHIPPING
Domestic Buyers
- We ship within 3 business days of payment, usually sooner
- We offer FREE shipping on all orders!
- We only ship to the lower 48 states, no APO/FPO addresses or PO Boxes allowed
- We have confidence in our products, but if you are not fully satisfied please contact us within 30 days of purchase and you will get full refund.
International buyers
– please note: Import duties, taxes, and charges aren't included in the item price or postage cost. These charges are the buyer's responsibility.
- Please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Warranty
The warranty shall not apply to the following circumstances:
a) Damage caused by undue ware tear, misuse, improper installation or operation, neglect, accidents.
b) Damage caused by natural disasters, flood fire, lightning or pollution.
c) If item was opened, any parts removed or repaired by any unauthorized person.
d) If damaged parts are the TFT screen or the screen has less than 3 dead pixels.